Activity

The baseline cases of these spaces are established according to the existing standards, guidelines or practices. Several integrated mitigation strategies are recommended and classified based on their relative cost and effort of implementation for each indoor space. They can be applied to help meet the current challenge of ongoing COVID-19, and provide better preparation for other possible epidemics and pandemics of airborne infectious diseases in the future.In this paper, we reflect on an emerging community-based partnership rooted in place-based reparative research. Braiding knowledges (Atalay, 2012) from Nbisiing Anishinaabeg communities, northern Ontario universities, and multi-scalar museums, the partnership focuses on repatriation, reparative environmental histories, and action-based research in the context of settler colonialism and climate change. We reflect on ongoing projects that attempt to put Anishinaabe gikendaasowin (knowledge) into action alongside historical geographical research. We discuss how the partnership resonates with community geography values of relationship, collaboration, equity, and reciprocity, and urge non-Indigenous geographers to acknowledge how Indigenous knowledges and approaches have shaped these ideas long before geography became a discipline. We contend that historical geographers have a deeper role to play in community geography scholarship, citing examples of two projects related to (1) repatriation of Anishinaabeg cultural heritage and (2) storymapping through historical Geographic Information Systems (HGIS). However, we argue, geographers must continue to acknowledge their own positionality in a discipline that was built through settler colonial violence and knowledge production. Finally, we reflect on the role of academic institutions in facilitating First Nation-university-museum partnerships through access to funding, space, and databases, while addressing the challenges of relying on institutional support for reparatory and decolonizing projects.We analyze the determination of the optimal intensity and duration of social distancing policy aiming to control the spread of an infectious disease in a simple macroeconomic-epidemiological model. In our setting the social planner wishes to minimize the social costs associated with the levels of disease prevalence and output lost due to social distancing, both during and at the end of epidemic management program. Indeed, by limiting individuals’ ability to freely move or interact with others (since requiring to wear face mask or to maintain physical distance from others, or even forcing some businesses to remain closed), social distancing has on the one hand the effect to reduce the disease incidence and on the other hand to reduce the economy’s productive capacity. We analyze both the early and the advanced epidemic stage intervention strategies highlighting their implications for short and long run health and macroeconomic outcomes. We show that both the intensity and the duration of the optimal social distancing policy may largely vary according to the epidemiological characteristics of specific diseases, and that the balancing of the health benefits and economic costs associated with social distancing may require to accept the disease to reach an endemic state. Focusing in particular on COVID-19 we present a calibration based on Italian data showing how the optimal social distancing policy may vary if implemented at national or at regional level.Many developing countries have highly unequal health systems across their regions. The pandemic of COVID-19 brought an additional challenge, as hospital structures equipped with doctors, intensive care units and respirators are not available to a sufficient extent in all regions. Using Data Envelopment Analysis, we create a COVID Index to verify whether the hospital structures in 543 Brazilian microregions are adequate to deal with COVID-19 and to verify whether public policies were implemented in the right direction. The results indicate that hospital structures in the poorest microregions were the most vulnerable, although the peak of COVID-19 occurred in the richest microregions (Sao Paulo). The Southeast states could relocate hospital resources or even patients between their regions. The relocation was not possible in many states in the Northeast, as the health system poorly assisted the interior of these states. These findings reveal that the heterogeneity of microregions’ hospital structures follows the patterns of socioeconomic inequalities. We conclude that it is easier for the wealthier regions to reallocate hospital resources internally than for the poorest regions. By using the COVID Index, policymakers and hospital managers have straightforward information to decide which regions must receive new investments and reallocate underutilized resources.The production of rapid tools for plastic molding, sheet metal forming, and blanking has always been a critical and important goal for applied research, and a very large number of alternative methods have been proposed over the decades for their production. Simufilam Among these methods, the use of extrusion-based additive manufacturing (EAM), such as fused filament fabrication (FFF) or similar technologies, has not been frequently considered and needs to be explored extensively. EAM is generally considered a low-cost, low-quality, low-performance class of AM and not suited to produce real functional parts, but only for aesthetical prototypes. However, the capabilities of EAM technologies have greatly evolved and now it is possible to extrude a wide range of materials such as polymeric materials including both the low strength polymeric materials (such as nylon or PLA) and the high strength polymeric materials (such as PEI and PEEK), metals (such as tool steel), and even ceramics (such as zirconia). Starting from an extensive literature review, the purpose of the present paper is to further demonstrate the potential applicability and versatility of EAM as a rapid tool manufacturing technology for different applications in shearing, bending, deep drawing, and injection molding.